单选题 当IGMPV3主机希望离开组播组G时,主机会主动发送Membership Report报文,报文中包含的组记录为

A、 TO_IN(A, G)
B、 TO_EX(A, G)
C、 TO_IN(Null, G)
D、 TO_EX(Null, G)
下载APP答题
由4l***mv提供 分享 举报 纠错

相关试题

单选题 以下哪个地址不属于IPv4组播地址

A、232.255.255.255
B、242.255.255.250
C、239.255.255.255
D、224.0.0.13

单选题 客户采购了一台路由器,如果此路由器性能指标为平均无故障工作时间MTBF>Y14 8年,平均维修时间MTTR

A、99.9%
B、99.99%
C、99.999%
D、99.9999%

单选题 当主机收到IGMPv2查询器发出的通用组查询(General Query)报文后,(选择一项或多项)

A、主机立即发送Membership Report报文
B、Report报文的目的地址与报文中的Group Address地址相同
C、Report报文的目的地址为224.0.0.1
D、主机只有收到通用组查询(General Query)后才会发送Membership Report报文

单选题 进行三层组播配置之前,首先需要进行配置是

A、进入IGMP视图
B、配置IGMP协议版本
C、配置PIM协议
D、通过multicast-routing-enable命令全局启用组播

单选题 客户的局域网交换机SWA双上行连接交换机SWB和交换机SWC,通过SmartLink保证链路可靠性,如果交换机SWA设备MAC地址为000f-e269-42d1,交换机SWB设备MAC地址为000f-e269-42d2,交换机SWC设备MAC地址为000f-e269-42d3,从上述信息可以得知

A、当交换机SWA连接交换机SWB线路故障,交换机SWA发送Flush报文的目的mac是000f-e269-42d1
B、当交换机SWA连接交换机SWB线路故障,交换机SWA发送Flush报文的目的mac是000f-e269-42d2
C、当交换机SWA连接交换机SWB线路故障,交换机SWA发送Flush报文的目的mac是000f-e269-42d3
D、以上答案都不正确

单选题 客户的二台交换机SWA、SWB通过七根以太网线连接在一起,并配置了静态链路聚合,交换机SWA上对应端口为Ethernet 1/0 Ethernet 1/0/2、Ethernet 1/0/3、Ethernet 1/0/4、Ethernet 1/0/5、Ethernet 1/0/6、Ethernet 1/0/7,配置方式为按照端口顺序依次配置,如果交换机SWA、SWB每个聚合组只支持6个端口,则

A、在各端口配置一致的情况下,Ethernet1/0/1端口为聚合组Unselected端口
B、在各端口配置一致的情况下,SWA在7个端口中随机选择一个端口为聚合组Unselected端口
C、在各端口配置一致的情况下,Ethernet1/0/6端口为聚合组Unselected端口
D、在各端口配置一致的情况下,Ethernet1/0/7端口为聚合组Unselected端口

单选题 210客户的二台交换机SWA、SWB通过七根以太网线连接在一起,并配置了动态链路聚合,交换机SWA上对应端口为 Ethernet 1/0 Ethernet 1/0/2、Ethernet 1/0/3、Ethernet 1/0/4、Ethernet 1/0/5、Ethernet 1/0/6、Ethernet 1/0/7,如果交换机SWA、SWB每个聚合组只支持6个端口,且SWA交换机有如下配置 [SWA]interface Ethernet 1/0/7 [SWA-Ethernet1/0/7]lacp port-priority 4096 设备上查看LACP状态输出如下: [SWA]display lacp system-id Actor System ID: 0x8000, 00e1-fc00-5000 [SWB]display lacp system-id Actor System ID: 0x8000, 00e0-fc43-7384 从上述信息可以得知

A、在各端口配置一致的情况下,Ethernet1/0/1端口为聚合组Unselected端口
B、在各端口配置一致的情况下,Ethernet1/0/2端口为聚合组Unselected端口
C、在各端口配置一致的情况下,Ethernet1/0/6端口为聚合组Unselected端口
D、在各端口配置一致的情况下,Ethernet1/0/7端口为聚合组Unselected端口

单选题 如图所示的网络中,交换机SWA为二层交换机,路由器RTA为各PC的网关,在路由器RTA上做了如下配置 [RTA]interface Ethernet 0/0 [RTA-Ethernet0/0]ip address 10.10.10.1 255.255.255.0 [RTA-Ethernet0/0]interface ethernet 0/2 [RTA-Ethernet0/2]ip address 20.20.20.1 255.255.255.0 [RTA-Ethernet0/2]vlan-type dot1q vid 2 [RTA-Ethernet0/2]interface ethernet 0/3 [RTA-Ethernet0/3]ip address 30.30.30.1 255.255.255.0 [RTA-Ethernet0/3]vlan-type dot1q vid 3 在交换机SWA上完成相应配置后,PCA、PCB和PCC都可以ping通自己的网关,下面交换机SWA端口Ethernet1/0/4的配置应为(选择一项或多项)

A、interface Ethernet 1/0/4 port link-mode bridge port link-type trunk Port trunk permit vlan all
B、interface Ethernet1/0/4 port link-mode bridge port link-type trunk Port trunk permit vlan all port trunk pvid vlan 2
C、interface Ethernet1/0/4 port link-mode bridge port link-type trunk Port trunk permit vlan all port trunk pvid vlan 3
D、interface Ethernet 1/0/4 port link-mode bridge port link-type trunk Port trunk permit vlan all port trunk pvid vlan 10